{"product_id":"blue-sensor-au-per-blue-connect-per-piscine-al-cloro-e-al-sale","title":"Blue Sensor Au for Blue Connect, for salt pools","description":"\u003cp\u003eBlue Sensor Au is compatible with Blue Connect digital analyzer.\u003cbr \/\u003e\u003cbr \/\u003e\u003cstrong\u003eVersion for pools treated with salt.\u003c\/strong\u003e\u003cbr \/\u003e\u003cbr \/\u003eOriginal Astralpool Fluidra spare part.\u003c\/p\u003e\r\n\u003cp\u003e \u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003eNB\u003c\/strong\u003e: To ensure maximum longevity of the probe, keep it for as long as possible in a humid environment. If you need to take the device out of the pool, screw it on storage cap with KCl (saturated potassium chloride), or pH4, or as a last resort, running water with a good amount of cooking salt as the probe should not be left dry.\u003c\/p\u003e\r\n\u003cp\u003e \u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003eProbe replacement\u003c\/strong\u003e\u003cspan lang=\"en\" class=\"Y2IQFc\"\u003e\u003c\/span\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cspan lang=\"en\" class=\"Y2IQFc\"\u003eThe replacement of the probe is necessary approximately every 2 years.\u003c\/span\u003e\u003c\/p\u003e\r\n\u003col\u003e\r\n\u003cli\u003eIn the app, in “Settings“ » ”My analyzer” » ”Probe settings”, press “Probe replacement“.\u003c\/li\u003e\r\n\u003cli\u003eTake out the analyzer from the water, remove the usage cap and start the procedure in a dry and clean place.\u003c\/li\u003e\r\n\u003cli\u003eWipe it with a clean, absorbent cloth, paying special attention to properly drying the bottom part of the product (where the probe is located) without touching the sensors.\u003c\/li\u003e\r\n\u003cli\u003eUsing the screwdriver, unscrew the screw located on the edge of the nut. If there are no screws, proceed to the next step.\u003c\/li\u003e\r\n\u003cli\u003eUnscrew the nut with the cloth. If you struggle to unscrew the nut, use adjustable pliers by placing them on this exact spot.\u003c\/li\u003e\r\n\u003cli\u003eUse a knife or a cutter to unlock the probe.\u003c\/li\u003e\r\n\u003cli\u003eRemove the probe making sure to keep the analyzer upright (with the top of the device above and the bottom part below) so that residual water does not penetrate into the product. Be sure to remove the seal and discard it. It could be stuck inside.\u003c\/li\u003e\r\n\u003cli\u003eWipe off residual water from the opening area and inside the hole with the cloth.\u003c\/li\u003e\r\n\u003cli\u003eTake the new probe, scan its QR code and remove the protective cap. Be careful not to drop the probe as it is a very fragile item.\u003c\/li\u003e\r\n\u003cli\u003eWipe the black plastic body of the new probe if needed. It should be perfectly dry. NB: Make sure the gold contacts on the top of the probe are clean (shiny) and dry. Otherwise, clean them with a cotton swab soaked in household alcohol.\u003c\/li\u003e\r\n\u003cli\u003ePlace the new seal supplied with the replacement on the new probe.\u003c\/li\u003e\r\n\u003cli\u003eInsert the probe and turn it until it is placed correctly. Three beeps are emitted within 15 seconds.\u003c\/li\u003e\r\n\u003cli\u003eScrew the nut all the way onto the device. Do not hesitate to use a cloth to tighten it properly to avoid hurting your hand.\u003c\/li\u003e\r\n\u003cli\u003eUsing the screwdriver, screw the screw (all the way but without forcing) on the edge of the nut. If there are no screws, proceed to the next step.\u003c\/li\u003e\r\n\u003cli\u003eThen, place the usage cap and place the analyzer back in the water.\u003c\/li\u003e\r\n\u003c\/ol\u003e\r\n\u003cp\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cspan lang=\"en\" class=\"Y2IQFc\"\u003e\u003c\/span\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cspan lang=\"en\" class=\"Y2IQFc\"\u003e\u003c\/span\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cspan lang=\"en\" class=\"Y2IQFc\"\u003e\u003c\/span\u003e\u003cstrong\u003eNB: \u003c\/strong\u003eThe sensor may take a few hours to stabilise its parameters after its first immersion in the swimming pool.\u003c\/p\u003e","brand":"Zavatti Shop","offers":[{"title":"Default Title","offer_id":52061981180246,"sku":"7015R002","price":179.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0952\/0588\/4246\/files\/blue-sensor-pt-per-blue-connect_1.jpg?v=1765411146","url":"https:\/\/www.zavattishop.com\/en\/products\/blue-sensor-au-fur-blue-connect-pools-mit-salz","provider":"Zavatti Shop","version":"1.0","type":"link"}